How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
What are your opinions about Tools You Need to Install a New Bathtub ?
Setting up a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall to remove the old tub as well as place the new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already bought a new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product list ought to consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location in between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least when as this will settle it into its final setting.
Planning for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about How to Install a Bathtub Yourself, I was thinking sharing that excerpt was smart. Loved our post? Please share it. Let another person locate it. Thanks a lot for taking the time to read it.
Book
Report this page